ECO Farm 800W CREE COB LED Grow Light Evaluation

January 17, 2020

1. Let’s measure the spectrum of the ECO FARM 800W LED grow light first  

  Now I hang up this light, put it straight and flat, and set up a coordinate system for spatial measurement of this light according to my previous practice of doing evaluation. As shown in the figure below: from the bottom of this light, which is the center point of the light bead face, vertically downward, is the z-axis.From the center of the bead face, the center line parallel to the long side of the rectangle is the X-axis, and the center line parallel to the short side of the rectangle is the Y-axis.

 

 We take two measurements, and we put them on the Z axis, 24 inches above the light, and we measure them.

  Here is the spectrum that we measured with this instrument, and we took it out of the instrument, and you can see that the spectrum is pretty good.

 

  Here is the spectrogram of the cannabis growing light under the brand Fluence, which is very well known in the cannabis growing light industry. You can refer to it. 

  As you could see that this light in the most important blue and red band is very good to meet our planting requirements, compared to the 480 to 600 band of light is less, we had better use a low power HPS high pressure sodium lamp, or CMH metal halide lamp to make up for it.

2. Let's measure the coverage area of this lamp.

2.1. Let's measure the spatial distribution of the light quantum flux density of this light first

  We placed the measuring mesh cloth with the dimensions I had drawn before directly under the light, and then measured the quantum flux density of light at each point on the mesh cloth by setting the distance between the light bead and the mesh cloth as 12 inches, 18 inches, 24 inches, 30.5 inch respectively.   

 

  The whole process is relatively tedious, the position and height are constantly changed. I have sorted out the specific measurement values for you and marked them directly on the measuring grid. As shown in the following four pictures.  

ECO Farm 800W COB CREE LED Grow Light photon flux density (μmol / m ^ 2 / s) the experimental measurement.

 

 

 

  Let's take the data from the above four measurements, and from the side view, we can make the following conical light distribution map.    

 

    A simple calculation method for the area covered by a cannabis planting light is to hang the lamp to a certain height to ensure the central photosynthetic effective light quantum flux density (PPFD) value is 150 μmol / m ^ 2 / s, within this radius, it can meet the lighting demand of hemp seedling period. 

  The other way is to find the distance between the boundary and the central point with the value of the photosynthetically available light quantum flux density (PPFD) of 600, which can meet the illumination requirements of the growing period and flowering period of cannabis within this radius.

     2.2. How much area can this marijuana planting lamp cover if used for marijuana seedlings?

  The appropriate illumination intensity of cannabis seedlings was 200±50 mol/m^2/s. We chose a small pot with a square mouth and the size of the pot mouth was 3.93 inches (10 cm). On the other hand, ECO FARM 200W LED grow lights can cover an area of 11 square feet , or 256 plants.  

 

  According to the measurement data, using the ECO Farm 800W LED indoor planting light in the seeding area, the height of the cannabis seedling top from the light is about 53 inches (134.62 cm), at this time, the maximum coverage radius is measured to be 32 inches . As shown in the figure below.    

 

   If the ECO Farm 800W LED lights are used in a large area of plant nursery, a light can cover an area of 5.3 feet times 5.3 feet is equal to 28.9 square feet. Because of the large area, the lights will stack up, and the edges will reach PPFD: 150 mol/m^2 s. As shown in the figure below.   

 

2.3. How much area can this led light cover for the growing and blooming period of cannabis?         

   We used a medium size pot with a square cut in the growing season. The pot size was 11 inches (27.94 cm).In growing season ECO Farm 800W LED marijuana light can cover 4 square foot area, namely 4 cannabis plants. The appropriate light intensity for adult cannabis was 800±200 mol/m2s. In habitat use ECO Farm 800W COB LED grow lights marijuana, marijuana blade tip from the height of the lamp is about 30.5 inches (77.47 centimeters).As shown in the figure below.

 

  For large areas where marijuana is growing and flowering, the LED lights require one light for every 4 square feet. Because a large area is uniformly arranged with multiple lights, the lights will be superimposed, so that the edges will also reach PPFD: 600 mol/m2·s.As shown in the figure below.

 

  From the above data, although the intensity of this lamp is particularly high, it has strong light gathering ability, that is, the illumination range is relatively small, and the coverage area is too small during the growing and flowering period. So if you are planting a large area, you need to arrange a lot of this light closely.

  So in my opinion, this light had better be used at seedling stage, if want to be used at growing area and flowering period especially when flowering period, had better cooperate with a kind of HPS high pressure sodium lamp or CMH gold halide lamp, can overcome this defect so.

 3. Let's check the quality of this light

 Finally let‘s took this lamp apart to see the inside situation, let's first look at the situation of the lamp bead, from the details of the lamp bead, this lamp bead is the lamp bead of the south Korean brand SAMSUNG. This kind of light bead is the main application in the plant lamp industry at present. It has a high photosynthetic quantum number efficiency and is a lamp bead that saves electricity.

 

  In addition, the heat dissipation is aluminum profile, aluminum plate is very thick, the heat capacity is large, aluminum radiator surface design is large enough, and aluminum profiles between grid ventilation design is also very good, and a large fan in the middle, can put the lamp bead as quick heat out.

   Judge from a few details above, this light, true quality is good.Mary, director of product sales at ECO FARM GREEN INC., told me they offer a three-year warranty on the light, with free warranty and replacement service for three years.I think the quality of this light will not be any problem after three years. 

4. Saving electricity bill  

  Finally we will light the lamp for a period of time, to see the actual power consumption, we use an electric power testing instrument to actually look at this lamp is really save electricity, first of all, we look at its instantaneous power, the display is 349 w, we found that there exists serious false targets, we know that in fact for high power plant lamp, qi phenomenon is very common, but the light of the actual power is worth its price, and its PPFD parameters are also really good, the smaller power is also save electricity, if the lamp is 800 w according to its coverage is too inefficient.

  Now let's all turn on this light for a while to test the actual power consumption.

 

  From the picture, we can see that we lighted this lamp for 915 minutes in total. The actual power consumption is only 4.98 kwh, and 24 hours is 1440 minutes. In this way, the power consumption for 24 hours a day is about 4.98 * 1440/915 = 7.84 kwh.

  At $0.125 a kilowatt-hour, you could cover 19 square feet of marijuana growing space for $0.98 a day. 1 square foot (sq.ft)=0.092903 square meters (sq.m), which is the area that can cover 1.78 square meters.   

  If you cover growing and flowering areas, you can cover 3.67 square feet.1 square foot (sq.ft)=0.092903 SQM (SQM), which is the area that can cover 0.34 SQM.

    If your room is 5 meters wide and 6 meters long and 30 square meters (323sq.ft), remove the non-growing area in the space, and the growing area is about 20 square meters, then 47 of these lights will be enough. The lighting time for marijuana growth is usually only 16 hours per day, so the real daily electricity cost should be 30.7 USD.

6. The following is my evaluation of the advantages of this planting light after the actual measurement

(1) the spectrum is very good, very close to the spectrum of the authoritative cannabis cultivation light of Fluence brand. 

(2) the illumination area is relatively large. In the 349-watt planting light, it can be regarded as illuminating a relatively large area. 

(3) The quality is really excellent, the main core components are the brand products produced by big factories, the application of three years should not be bad. 

(4) The price is really cheap. You can hardly find a cheaper 349-watt grow light on the market. 

   At this point, we have completely evaluated this light. If you are interested in this lamp or other products, you can contact Mary, product sales director of ECO FARM GREEN INC. Her contact information is: her email address is business@ecofarm.ca, WhatsApp is +86 13155136939, or directly through the sales link of the following products.   Finally, I am very happy to share with you all kinds of interesting things about marijuana. Please also help me to like, share, and comment on this review so that more people can see it and let us have greater influence. 

 https://www.ecofarm.ca/products/eco-farm-cree-cob-led-grow-light?_pos=9&_sid=70d8db0aa&_ss=r